Ladder Operations Manual Practice Test

These questions are part of the practice quiz. Start practicing

• Which condition indicates composite blades should be changed?
• What is the wattage of the Tele-lights?
• What is the Ventilation Position for ground ladder placement?
• What is the mechanical advantage when forcing with the forks with 3 inch set in the jam?
• What is the process called when switching a tiller ladder from rescue to water mode?
• How many CFD platform ladders are there and who manufactures them?
• How do you lubricate the Hydra-RAM II?
• When is a structure considered not clear with respect to searches?
• At what ppm reading should personnel leave the structure and return with an SCBA?
• What are the three categories involved in natural gas delivery?
• What is the force required to extend ground ladders?
• What is the recommended source for HVAC control guidance during initial ventilation?
• If fire conditions do not allow for immediate entry and victim survival is improbable, what must the IC air over the radio?
• What is the initial IC responsible for developing, which includes either an Investigation Plan or a Fire Attack Plan and Search Plan?
• What is the diameter of the Yellow mainline in the CFD Search bags?
• What are the operating speed and air output of the Gas RAMFAN GX200?
• What is the recommendation regarding fuel controlled vs ventilation controlled fires?
• Which of the following is NOT listed as a use of K-100 fuel additive?
• Should you cut the bare aluminum support for the drip loops?
• What is the weight of the Stihl 220 MSA C chainsaw?
• What should be open when retracting the platform aerial?
• Where is the locking carabiner located in the CFD search bags?
• What does the TIC offer the user?
• What is the Sutphen ladders EPU duty cycle?
• The first ladder is placed on which side of the structure to support a 360 assessment?
• When performing a plunge cut, what should you be mindful of?
• Failure to coordinate vertical ventilation could cause rapid release of products of incomplete combustion and quick transition from ventilation controlled to fuel controlled, which could result in rapid fire growth.
• What should be done prior to removing the carburetor box cover?
• For a CO Alarm response, what units are sent based on symptomatic vs asymptomatic response?
• How many inches of extension is needed for access to the safety pins for the SP-100 outriggers?
• Where will the third due ladder crew be assigned?
• Which statement about the Stihl MSA 220 C Chainsaw is true?
• What is the cutting depth of a 12 inch blade?
• Can you move the aerial to the short jacked side?
• What temperature does the quartz light operate at?
• How often should EPUs be run?
• Where should the command post be located?
• What significant change occurred when the division purchased Pierce tillers?
• What is the fuel capacity of the EU1000i Honda generator?
• Who maintains the list of approved PPE modifications?
• What happens if you perform sudden stops when operating the tiller aerial levers?
• What is cold smoke?
• When checking the Honda generator oil, where should the oil reach on the oil cap?
• What is the sequence of knots at the 50-foot, 100-foot, and 150-foot marks?
• What is the idle RPM of the Stihl MS 500i chainsaw?
• NPV is typically used during which scenario?
• How far from the structure should the initial CO reading be taken?
• What is the proper first step when back feeding the truck with a back-up generator?
• Can you use the high idle function when the platform is in pump gear?
• If it feels like more than 75 lbs of force, what should you do?
• What is the purpose of Teepee cut's overlapping instruction?
• What is the pump rating on the platform ladders?
• What is a key feature of Tele-lights regarding connectivity?
• How is the flow path defined in fire behavior?
• By how much did injuries decrease when loggers were informed of Kickback?
• How do you counter Spring Pole?
• What phrase is aired over the radio upon completion of the primary search?
• Stihl MS 046, 460, and 461R chainsaws are characterized by which of the following?
• What is the maximum output in watts for the EB5000X for up to 10 seconds?
• Which criterion is required for non-issued PPE to be approved for use?
• What NFPA reg handles structural firefighting PPE?
• Which ladder has the longest cooldown after operation?
• What is the fuel capacity of the EU2000i Honda generator?
• The pump rating on the platform ladders includes a capability of up to what GPM?
• Which accessory is included with the tiller ladder waterway tip?
• How many openings are needed for natural ventilation?
• What standard must eye protection meet?
• What voltage and frequency options does the Supervac HF164E support?
• How far should ladders and aerials be kept from energized electrical equipment?
• What is the CH4 low alarm level on the P-400 gas monitoring system?
• Which statement about the rope marking system is true?
• Where should you cross on the roof of a strip mall?
• What gauge is used for the Stihl MSA 220 C chainsaw chain?
• What is overhaul's main purpose?
• Where is the high hazard location along the flow path?
• Which blade is described as multipurpose with carbide teeth?
• Composite blades are described as what?
• What must be done by the first arriving company or division member at the scene of a fire?
• What are the hazards of Plunge/Bore Cutting?
• What is the dry tip load of the ALF aerials?
• What happens if a heat sensor turns black due to heat exposure?
• Which statement is not described as a benefit of smart meters?
• Which device has 1/3 HP and 5,200 cfm output?
• Vertical ventilation must be performed with what?
• Which generator model has a maximum rating of 5.0 KVA for up to 30 minutes?
• Can Division circular saws use blades with an arbor os 25mm?
• Personnel shall not operate over top what type of roof structure?
• All companies shall bring what to the designated accountability location?
• What is the operating engine temperature of the trucks?
• What is the running oil pressure of the trucks?
• Which statement about cold smoke is true?
• What is the CO low alarm level on the P-400 gas monitoring system?
• Prior to bedding the tiller aerial, what should be checked?
• Which of the following describes the rating specification for the fiberglass hot stick?
• When reaching a downed firefighter, where should the rope carrying firefighter place himself?
• What is the cold crank wattage of the yellow box fan?
• Which action will limit fire growth along the flow path?
• What is the cutting depth of a 14 inch blade?
• What can be used to initially support a stream from the tiller ladder waterway?
• Which statement is true about the fuel used in Honda generators regarding ethanol content?
• What are the methods of block wall breaching ?
• Which option is NOT listed as a tying-off method for the search rope?
• What is the SP-95 platform tip load when dry?
• How many firefighters are required to perform the initial investigation of a gas leak?
• Where should all remaining companies stage for a gas leak response?
• What is the continuous operation rating (KVA) of the EB5000X?
• Which is a listed disadvantage of platform ladders?
• What lubricant is recommended for moving parts on ground ladders?
• What is the key to that maneuverability?
• Which type of staples does the Arrow Stapler use?
• Which hood material is listed as part of the PPE set?
• For longer storage, what is the K-100 ratio per gallon of gas?
• Which item is not listed as a consideration for removal of a victim?
• High pressure is defined as which range?
• What should we be mindful of when using the Gas RAMFAN GX200?
• What is the stated range for the stack tip sizes on the tiller ladder waterway?
• Which statement about the 700 circular saw is true?
• What is the H2S high alarm level on the P-400 gas monitoring system?
• How many knots are present at the 50-foot mark?
• What happens when the Oil Alert indicator detects low oil?
• What is the blade length of the Stihl MS 500i chainsaw?
• What should be done after finding a smart meter during an incident?
• Which extinguishers should be used on energized electrical equipment?
• What hazards are associated with residential metal roofing?
• What is the fiberglass hot stick rated to?
• Which area is addressed last in the Primary Search and Evacuation plan?
• What is a stated advantage of two-stroke engines over four-stroke engines?
• What are considerations for removal of a victim?
• How can you distinguish Pierce tiller aerials from American LaFrance tiller aerials?
• A 50:1 fuel mix is typically designed for which type of engine?
• According to guidelines, when should the chain be replaced on a chainsaw?
• What is the wind rating of the CFD platforms?
• Which component is responsible for generating the electrical spark in these engines?
• The working side outriggers must what?
• Vertical ventilation is the...
• How many Ladders are included in a Fire Response (Report of a fire)?
• Which standard governs eye protection in PPE guidelines?
• What should be the mindset of the first arriving Ladder company?
• If a floor runner measures 30 inches by 25 inches, what is its area in square inches?
• Which pair correctly matches the dry tip loads for Pierce and ALF aerials?
• What is the cutting depth for the 12 inch circular saw blade?
• What are the stack tip sizes on the tiller ladder waterway?
• What is the run time of the Gas RAMFAN GX200?
• What is the EB5000X run time at half load?
• What is the rung spacing for NFPA ground ladders?
• How many Rescue units are included in a Fire Response (Report of a fire)?
• What is the arbor size and rpm rating for our circular saw blades?
• From what date is the 10-year service life of structural firefighting PPE counted?
• Which blade type is described as cuts metal/concrete?
• Why is falling slate particularly dangerous?
• What is the displacement of the Stihl MS 500i chainsaw?
• What should you do with the battery when performing maintenance or changing the chain on the Stihl MSA 220 C?
• What is the maximum engine speed of the Stihl MS 500i chainsaw?
• What is the run time of the EU2000i under full load?
• Which factor is included in the rescue size-up regarding the ability to enter and control the incident?
• What should be done when readings are between 15 ppm and 35 ppm?
• What do the buzzer presses denote?
• Which statement is true about 15 amp vs 20 amp Hubbell connections?
• What part of the truck determines the scrub area?
• The spark plug gap specification for chainsaws is most accurately described as which measurement?
• Forcing entry should be thought of as....
• Which of the following is NOT a listed use for the Stihl 220 MSA C Chainsaw?
• What is listed on most cord bags?
• Which of the following describes the correct sequence for roof cuts?
• What is the reach of the 12 ft division ground ladder?
• What is contained in the red tagline bags?
• In the 461R chainsaw, what does the R signify?
• What is the reach of the 28 ft division ground ladder?
• How many tillers ladders are there, and who makes them?
• Which statement best describes the capability of smart meters in terms of power control?
• On a gas leak response, where will the first arriving BC establish the command post?
• For Division circular saw blades with a 20 mm arbor, what is the minimum RPM rating they should meet?
• Which of the following is NOT listed as a size-up factor during the 360?
• When venting a commercial roof, how far from the roof edge is good practice?
• Which of the following are the specifications for the RAMFAN EFC150X (New Red Box Fan)?
• What is the mechanical advantage of gapping the door with a 2 inch adz on a 30 inch Pro-Bar?
• What is the first step in the forcible entry algorithm?
• What is the service life of structural firefighting PPE from the date of manufacture?
• What is the AC output of the EU2000i Honda generator?
• What octane rating and ethanol limit does Stihl recommend for gasoline?
• What fuel mix ratio is listed for the Stihl TS400 and 700 series circular saws?
• How many watts are required to run a quartz light?
• What does the rating of the fiberglass hot stick refer to?
• Can the on board generators be run while driving/responding to a scene?
• What is the spindle speed of the TS 500i circular saw?
• In natural gas delivery, which sequence lists the three categories from resource to consumer?
• When should the supply line to the ladder be charged?
• What hazards are posed by rain roofs?
• What is the SP-95 platform load when water is flowing?
• What is the CO high alarm level on the P-400 gas monitoring system?
• How many Engines are included in a Fire Response (Report of a fire)?
• What is a plunge cut used for?
• How is roof pitch measured?
• Salvage involves which of the following?
• Which statement is true about preparing to pump water to a platform?
• What oil specification and amount are used in the EU2000i Honda generator?
• What equipment should the USE group have?
• What is the rated wattage of the EU2000i Honda generator?
• Which tool has a 4 inch spreading distance?
• What is the CH4 high alarm level on the P-400 gas monitoring system?
• What engine is used in the EU1000i Honda generator?
• What is the 20 amp setting used for on the Electric RAMFAN EV400?
• How many sections does the SP-100 platform have?
• How many firefighters should be involved in breaching a block wall?
• What voltage powers the lights and ventilation for the elevator system?
• What thickness of plastic sheeting do ladders typically have?
• Which direction does a door open if no hinges are visible?
• When can the positive pressure fan be turned on?
• For the Stihl MS 046, 460, and 461R chainsaws, how many drive links and cutting teeth does the chain have?
• Access to the SP-100 outriggers' safety pins requires how many inches of extension?
• Dax blades are used for which applications?
• For positive pressure ventilation (PPV), where should the fan be positioned in relation to the opening?
• Which direction does a door open when hinges are visible?
• What is the unique use of the yellow box fan?
• What are the Rabbit Tool's spread distance and spreading force, with purchase point required?
• What type of staples does the Duo-Fast stapler use?
• Which statement about Spring Pole is true?
• What is the load capacity of the SP-95 platform when dry?
• What is the Rescue Position for ground ladder placement?
• How many feet of rope are in the yellow search rope bags?
• Which of the following is a listed use for the 046, 460, 461R chainsaws?
• When are ground ladders tested annually and by whom?
• What is the normal run wattage of the yellow box fan?
• What is the H2S low alarm level on the P-400 gas monitoring system?
• What is the load difference between dry and flowing water capacities?
• Which feature is an advantage of platform ladders?
• What is the horsepower of the Gas RAMFAN GX200?
• What octane of gasoline should be used in the Honda generator?
• Should the secondary search be completed by the same company that completed the primary search?
• How big is the collapse zone?
• Transmitted and Stored Thermal Energy Testing is required in which scenario?
• Which statement best describes forcible entry?
• Which description represents an open system for the halyard of an extension ladder?
• Which device has an air output of 4,459 cfm?
• Which thickness combination is typical for ladder plastic sheeting?
• Define natural ventilation.
• What is the stated weight rating with a safety factor for NFPA ground ladders?
• For Honda generators, how long can you operate between rated and maximum power?
• What is the output in CFM of the yellow box fan?
• What tool is used for the plunge/kerf cut?
• For division members to wear non-issued PPE, which statement describes the approval conditions?
• Which statement best describes the purpose of placing ladders for interior teams?
• What is the AC output of the EU1000i Honda generator?
• How much stronger are ground ladders with fly out?
• What is the reach of the Sutphen platforms?
• What is salvage?
• What octane rating does the Division recommend for gasoline?
• Why is it advised to cross the roof near the front of a strip mall?
• Define horizontal ventilation.
• What is the transmission operating temperature?
• What is the oil specification and amount used in the EU1000i Honda generator?
• Which statement correctly describes the EPU motor power?
• Which step typically follows Gap in the forcible entry algorithm?
• Upon fire control being achieved, which activity should the IC direct?
• What is the initial ventilation priority at a High-Rise incident?
• How should you operate the levers on the tiller aerials?
• What purpose does excess flow valves serve?
• How many stages are there in a four-stroke engine cycle?
• Which statement correctly describes the meaning of 'Open' on smart meters?
• What are the three stages of the Hydra-RAM II hydraulic system?
• Which devices are shed first by the load manager when reducing electrical load?
• May Division members wear non-issued PPE, and if so, under what conditions?
• What is the guiding principle when performing any ventilation action?
• During VEIS, what action is appropriate upon entry into the room?
• Who forms the Upper Search and Evacuation (USE) Group and who is the supervisor?
• In what order should rescue efforts be extended?
• Jack pads should be used at all times because they prevent what?
• What is the correct oil specification for Honda generators?
• What unit is used for the transmission operating temperature?
• What should be done to the guide bar after each use?
• What are the two back up generators CFD trucks may have?
• Which term is NOT listed as a method of mechanical ventilation?
• Which statement is true about slate roofs?
• Which action is part of a successful VEIS?
• Which range defines the Medium line operating pressure?
• Which statement about cord bags is true?
• When performing any ventilation, what must be considered?
• Which condition indicates Dax/Diamond blades should be changed?
• For PTO generators, what RPMs need to be below to engage the hydraulic motor?
• Before any ventilation is performed, what must the firefighter understand?
• Where are the control panels for Machine-Room-Less (MRL) elevators typically located?
• Which option is sometimes found on ladder cord reels?
• What is the spreading force of the Hydra-RAM II?
• What orientation are windows found in balloon frame construction?
• What does the load manager do?
• What type of cut is more taxing than the Teepee cut but also offers a larger opening through garage doors?
• What is the correct sequence for engaging the levers and the EPU to prevent deadheading?
• Which statement about Open on a smart meter is correct?
• What form is used to request a PPE modification?
• Which statement about rain roofs poses a safety hazard?
• In ventilation planning, the ventilation should be limited to which side of the building before fire control?
• For hydraulic ventilation, what percent of the window opening needs to be covered with a fog pattern?
• Who should you coordinate any type of ventilation with?
• Which statement correctly describes the safety concern related to solar panels?
• What is the oil pressure when idling?
• Which of the following is true about SP-100 platform specifications?
• Which option best describes safe hand positioning to prevent Kickback?
• What is the extension length and total spread of the SP-95 outriggers?
• Which fan operates at 3,590 RPM?
• What is the scrub area?
• Which statement correctly describes the reach comparison between the American LaFrance and Pierce tillers?
• What are the stokes basket arms rated to per pair?
• All electrical wires and equipment shall be considered energized. True or False?
• What should be done for readings 15 ppm or below?
• Ground ladders shall be placed in service when which condition exists?
• What is required when switching the tiller ladder from rescue to water modes?
• What is the algorithm for forcible entry?
• How do you prevent kickback when plunge cutting?
• During chainsaw maintenance, what should be done if any spurs are found on the guide bar?
• Which tool provides 8,000 lbs of spreading force?
• Which roof structure type is prohibited to operate over the top when it has been impacted by fire damage?
• What NFPA standard applies to ground ladders?
• What is the essential step before water introduction when preparing to place the platform into pump gear?
• American LaFrance aerials are which color?
• During morning checks, in which mode should the aerial be pinned?
• What is beneficial about smart meters found on homes?
• What engine is used in the EU2000i Honda generator?
• What is the maximum spindle speed listed for the TS400 and 700 series circular saws?
• What purpose does the inspection hole cut serve in commercial roof ventilation?
• How many 50-foot sections are in a 200-foot rope?
• What is the dry tip load of the Pierce tiller aerials?
• Where is the electrical charge created when the flywheel spins?
• What does RECEO VS stand for?
• Which statement accurately describes cold smoke in firefighting contexts?
• Time is what regarding the performance of a primary search?
• Which device has Cold crank wattage of 2,000 watts and Normal run wattage of 700 watts?
• What is the primary advantage of a tiller ladder?
• Which are safe guards to prevent Kickback?
• What type of wax should be used and how often should ladders be waxed?
• How many heat sensor labels are there per ladder section?
• What determines the methods used during forcible entry?
• What is the recommended next action after occupants have been evacuated due to elevated CO?
• What is the immediate action to take when a dangerous CO reading is detected and occupants are present?
• Supply lines should be laid when interior crews are expected to use more than what percentage of the water tank?
• Which tool has a 6 inch spreading distance?
• K-100 fuel additive should be used with which fuel types?
• How often should the halyard be inspected?
• After connecting the back-up generator to the truck's outlet, which action completes the sequence?
• Which statement correctly describes the 50:1 gasoline-to-oil ratio?
• Which statement is NOT true based on the tiller operation notes?
• What should be used for cleaning ground ladders?
• Which feature allows water to be controlled at the bucket?
• In chain drive-link color coding, which color indicates a low kickback chain?
• Readings are above 35 ppm for CO. What is the recommended immediate action?
• What is the specific gravity of natural gas?
• Which of the following is a factor the IC must consider when developing a basic rescue size up?
• What NFPA reg contains the standards for station/work uniforms?
• Which of the following is a disadvantage of platform ladders?
• When cutting Puck locks, where should you cut?
• Which of the following is the recommended climbing angle for the Rescue Position?
• Which statement best describes the effect of keeping doors closed during a fire to influence the flow path?
• What is the listed weight range for the TS400 and 700 series circular saws?
• What is the maximum ethanol content allowed in the gasoline for the Honda generators?
• What is the horsepower of the Battery RAMFAN EX50Li?
• Which statement best describes the Stihl MSA 220 C within its division?
• What is the spark plug gap specification for Honda generators?
• To whom should the PPE modification PI-32e be submitted?
• What are the voltmeter readings?
• What is the length of one extended outrigger on the SP-100 platforms?
• Which of the following is the specification set for the Supervac P164SE (Old Red Box Fan)?
• What type of oil is used in the Honda generators?
• Which statement best describes the strength improvement of ground ladders with fly-out?
• What are the battery specifications of the Battery RAMFAN EX50Li?
• Which reminder is important when moving beyond the hose line while searching for the seat of the fire?
• Which is a principle of Fire Flow Path?
• What does Open mean on smart meters?
• What is the spreading force of the Hurst Rabbit Tool?
• Which ladder EPU has a 2-minute operation window with a 5-minute cooldown?
• Which of the following describes the role of the turntable on a ladder truck?
• Which statement describes the engine type used in the Stihl TS400 and 700 series circular saws?
• What must be done prior to putting a platform in pump gear?
• During back feeding, which device must be slid to enable the auxiliary breaker?
• What is a consideration when performing Positive Pressure Ventilation?
• Which fan has an air output of 21,760 cfm at 3,450 RPM?
• How is the EPU motor powered?
• What is the length of the Yellow mainline in the CFD Search bags?
• In what order should roof cuts be made?
• Which of the following is explicitly part of the IC's salvage operations responsibilities after fire control?
• What is the displacement of the TS 500i engine?
• What is the cutting depth for the 14 inch circular saw blade?
• What should be known prior to opening the tillers waterway?
• How many turns are required to open or close a Post Indicator valve?
• Which statement about SP-100 is true?
• How many Battalion Chiefs (BC) are included in a Fire Response (Report of a fire)?
• What are the Hydra-RAM's spread distance and spreading force, with purchase point required?
• How many ground ladders is the driver responsible for on buildings with two or more floors?
• Horizontal ventilation must be performed in coordination with what?
• What is the max weight in the bucket if the stokes arms are being used?
• What type of ladders are used by the division?
• What size is the patch, logo, or emblem permitted to be on PPE?
• When using rope to remove downed wires, where should the rope be placed on the wire?
• What is the total jack spread of the SP-100 platforms?
• What is the run time of the EM6500SX at half load?
• What is a safety guideline when working on slate roofs?
• What is the reach of the American LaFrance tillers?
• When working in buildings with drop ceilings, what should you pay attention to?
• What equipment can be brought for a broken sprinkler head?
• Which trucks have Command Lights installed?
• How big of a hole should you cut for larger structures?
• What is the Pierce ladders EPU duty cycle?
• Which ventilation pattern is recommended to cover the window opening during hydraulic ventilation?
• What is the tiller aerials minimum tip load?
• Which item is NOT listed as part of a complete PPE set for firefighting?
• What stance should firefighters take toward salvage?
• Which action should be taken when a smart meter is found during an incident?
• What is the definition of Spring Pole?
• Pierce aerials are which color?
• How many knots are at the 100-foot mark?
• What is the minimum PPE required to operate a pump or aerial?
• Which item is NOT listed as equipment for the USE group?
• What setting does the Division set on chainsaws for their oil quantity control on the bottom?
• What is the maximum wattage of the EU2000i Honda generator?
• How many inches of adjustment does the blade guard have on the circular saws?
• What is defined as vertical ventilation?
• How many volts does the Electric RAMFAN EV400 require?
• Which of the following is NOT a listed type of elevator?
• In a 50:1 fuel/oil mix, how many fluid ounces of oil are required per gallon of gasoline?
• Which maintenance practice is recommended for circular saws?
• What button should you hit while responding in a PTO generator truck?
• Where should halyards be adjusted and retied?
• What size supply line is needed for flowing water for a platform?
• What must be done when a CFD company forces entry and no occupant/responsible party is present to maintain security?
• What does the eco throttle switch do when switched on?
• What type of staples does the Arrow Stapler use?
• In the proper back-feed sequence, which step comes immediately after starting the back-up generator?
• What is the minimum collapse zone expressed as a multiple of the building height?
• What is the dry load capacity of SP-100 platforms?
• The critical factor for secondary searches is what?
• Do attic ladders, Fresno ladders, and Little Giants meet NFPA specifications?
• Where should the Tiller/OSV firefighter throw the first ladder?
• What position will the first due ladder take?
• What is the SP-100 load capacity when flowing water?
• What is the priority for the Primary Search and evacuation plan in a High-Rise?
• What type of cut is used on garage doors?
• What should the gap setting of spark plugs for chainsaws be set to?
• What is the noise level generated by the Gas RAMFAN GX200?
• Which statement reflects a correct approach when a CO alarm is sounding?
• Who determines the appropriate PPE for rescue or special operations incidents?
• Is the structure considered clear due to statements from occupants?
• What size should supply lines be?
• In a 50:1 fuel mix, how many fluid ounces of oil are added per gallon of gasoline?
• What ventilation factors affect fire growth and development?
• How often should the oil be changed in Honda generators?
• What is Pull In?
• Which blade is used to cut gravel and asphalt commercial roofing?
• What horsepower is the Supervac HF164E (Yellow Box Fan)?
• Diamond blades are described as what?
• What is the primary purpose of the scrub area in aerial operations?
• When performing fire attack or ventilation during wind conditions what should be considered?
• If you want to stop movement, what should you do?
• Which ladder EPU has the shortest cooldown after operation?
• Which is the correct chain gauge for the Stihl 046, 460, and 461R chainsaws?
• With a 14 inch blade, what is the cutting depth of the TS 500i circular saw?
• How many Medic units are included in a Fire Response (Report of a fire)?
• What is the run time under full load for the EU1000i Honda generator?
• What is the fuel tank capacity of the EB5000X?
• If you must evacuate the apparatus when touched by electrical equipment how should you exit the vehicle?
• General care and maintenance for the 046, 460, 461R chainsaws includes which directive?
• What technology is used to construct the buckets of the platform ladders?
• What is the air output of the EV400 at the 15 amp setting?
• When should the driver be especially mindful while driving?
• What are the air outputs for the Battery RAMFAN EX50Li?
• Forcing the door should be thought of as what?
• Which document is developed by the Incident Commander to coordinate the response at the incident scene?
• For readings between 15 and 35 ppm, which sequence is correct?
• Cutting of drip lines is permissible on which structures?
• What hazards are posed by solar panels on a roof?
• For gas leak operations, which positioning best describes where the command post should be established?
• What is the horsepower of the Electric RAMFAN EV400?
• Which item is included in the PPE set for protecting the hands?
• What is the reach of the SP-95 platform?
• What voltage powers the elevator car mechanisms?
• Where does the second due ladder attempt to position?
• Which trucks are Night-Scan lights found on?
• What is the primary objective for ground ladder placement on scene?
• Hydraulic elevators are typically limited to how many stories?
• Which statement is true about tiller maneuverability?
• What are the O2 alarms for the P-400?
• What is the minimum width between ladder beams?
• Low pressure is defined as up to what?
• Which description represents a closed system for the halyard of an extension ladder?
• Firefighters should be what in regards to salvage?
• Who should you contact for halyard replacement?
• What is K-100 fuel additive used for?
• Which action reflects the salvage-focused step after fire control?
• What cut is used to remove carriage bolts?
• What are the two Hubbell lock connections encountered on CFD ladders?
• Which materials should be avoided during suppression activities due to their tendency to melt when exposed to heat?
• Which statement best describes Kickback mechanics?
• What is the first step in the start-up procedure for the TS 500i circular saw?
• During morning checks, in which mode should the aerial be pinned?
• Which automatic engine stop functions are present on both EB5000X and EM6500SX?
• What is the speed of the yellow box fan in RPM?
• Should attack stairwells be used for evacuation?
• What is Push Back?
• Which of the following is NOT listed as a method for mechanical ventilation?
• What does TIC stand for in the USE group equipment?
• Which statement about K-100 uses is correct?
• Kickback safety statement: True or false?
• Which ladder EPU has a 2-minute operation with a 7-minute cooldown?
• According to maintenance guidance, oil should be changed after which is earliest?
• Should on scene companies rely on reports from occupants or bystanders regarding the presence of victims?
• What is the rung load tested capacity for NFPA ground ladders?
• Which items should be worn on roadway incidents by personnel not actively engaged in suppression?
• What is the voltage draw of the Battery RAMFAN EX50Li?
• How many impellers does the Gas RAMFAN GX200 have?
• After exiting, how far should you be from the apparatus?
• What does the red indicator light signify on the Honda generator?
• What is the reach capability of the Pierce tillers?
• Approximately how large are floor runners?
• Which statement correctly lists the tiller ladders and manufacturers?
• In gas leak response, what is a key requirement before IC notification for remaining companies?
• What is the ALF ladders EPU duty cycle?
• Which statement is listed as an advantage/disadvantage of the 046, 460, 461R chainsaws?
• What is the maximum engine speed of the TS 500i?
• Which activity is directed by the IC upon fire control being achieved?
• Which activity involves evaluating salvage potential after fire control?
• What are the three commands when using the Irons?
• What component is included with the cord reels?
• Which of the following is NOT a category in natural gas delivery?
• What is a good initial pressure for the tiller ladder waterway?
• In a four-stroke engine, the piston fires every how many degrees of crankshaft rotation?
• Dax circular saw blades are which type?
• What is the continuous VA rating of the EM6500SX?
• AP 300 S battery indicator: What does 4 flashing red LEDs indicate?
• Which of the following is an advantage of the Stihl 220 MSA C Chainsaw?
• Which is a DC run time for the Battery RAMFAN EX50Li when using four battery packs?
• Which amperage option is listed for the cord reels?
• Which of the following describes the second due ladder's required approach?
• What is the HCN high alarm level on the P-400 gas monitoring system?
• What is the stated length of the cord reels on ladders?
• How should the generators be stored to prevent fuel spillage?
• If water must be used to extinguish an electrical fire, what guidelines should be followed?
• What is the standard mixing ratio of K-100 per gallon of gas?
• What is the HCN low alarm level on the P-400 gas monitoring system?
• How often are the knots in the rope spaced?
• What should the air pressure reading be for the ladder trucks?
• How many feet of rope are in the tag lines for the search bag?
• What is the idle RPM of the TS 500i?
• Kickback is described as which of the following?